Industrie Aktuell
News portal for construction and development

measurementSensor + Test hall 1, 215 Stand

Analog microelectronics expands its digital board level Miniature pressure sensors AMS 5915 with I2C output by special variants for Pneumatics Applications. These circuit board mountable sensors in the ceramic DIP-08 housing are designed for manifold mounting on flanges with O-ring seals. They are only about 4 mm high. The pressure sensors are suitable for both relative pressure and differential pressure measurements up to 16 bar with an overpressure resistance of 30 bar.

The AMS 5915 force sensors are suitable for both relative pressure measurement and differential pressure measurement up to 16 bar with an overpressure resistance of 30 bar. Due to their special design, the sensors are liquid-compatible on one side, ie in the case of relative pressure measurements, non-corrosive liquids can also be measured in addition to gaseous media thanks to the back pressure.

The high-precision, digital miniature pressure sensors have a resolution of 14 bit and, with their I2C interface and a supply voltage of 3,3 V, are ideal for microcontroller applications. They are digitally calibrated, linearized and temperature-compensated in a wide operating temperature range from -25 ° to +85 ° C, whereby a low total error of TEB <0.5% FSO is achieved in the entire operating temperature measuring range. The combination of a high-quality MEMS element with a modern mixed-signal IC on a ceramic substrate guarantees high long-term stability. With a response time of typically only 0,5 ms, the sensors are also suitable for fast measurements.


Another contribution of the manufacturer This e-mail address is being protected from spambots To display JavaScript must be turned on!

More news from pneumatics

  • SMC presents the improved soft start valve series AV-A for pneumatics. The valves are very compact and offer up to 2,2 times higher flow. You need 80% less energy than the previous models. The possible uses of the revised soft start valves increase significantly with the flow rate up to 13.400 l / min. They are ideal for slowly building up pressure e.g. B. during commissioning. This also applies to the quick venting of pneumatic systems, such as when switching off.
  • Sensor + Test Hall 1, Booth 215 Analog Microelectronics is expanding its digital board-level miniature pressure sensors AMS 5915 with I2C output to include special variants for pneumatic applications. This circuit board mountable sensor in the ceramic DIP-08 housing is designed for manifold mounting on flanges with O-ring seals. They are only about 4 mm high. The pressure sensors are suitable for both relative and differential pressure measurements up to 16 bar with an overpressure resistance of 30 bar.
  • “StarboxXT” and “Starbox2” are the names of the new spin-on separators from Mann + Hummel for the air de-oiling of compressors. The separator series ensures clean compressed air and at the same time reduces the energy consumption of the systems.
  • Loads of up to 4000 kg per m² can be conveyed gently and practically without friction on an air film on the “Fixed Glide” ball roller elements from Orimair. This is particularly advantageous in the case of soft and sensitive surfaces, since the load is taken up over a large area and not at points.
  • Hannover Messe Hall 3, Stand M43 The Heinrich Kipp plant has added a wide range of new clamping elements to the existing range. The new products are characterized by their pneumatic functionality and are particularly suitable for use in machine tools. Processes are considerably simplified by partial automation.
  • RS Components has greatly expanded its range of pneumatic components. In addition, there is a complete range of very inexpensive products under the own brand "RS Pro" and now also delivers to the EMEA and Asia-Pacific regions. In addition to the previously available pneumatic systems in the series, new products are aimed at maintenance engineers and machine builders.
  • Motek Hall 3, Booth 3301 The pneumatic linear unit LSM-3 from Friedemann Wagner is a precise and repeatable mini linear slide for pneumatic automation of especially small workpieces. The load to be moved is safely guided and carried by 2 carriages with sealed recirculating ball guides.
  • Up to 27% less weight than their predecessors, the new throttle check valves in a straight version with plug connection of the series AS-2F-A weigh on the scale. At the same time, SMC Germany has revised many details that improve handling:
  • Durable and robust C31 dome pressure reducers from IMI Precision Engineering are particularly low-maintenance. They can be used universally and are suitable for numerous industrial applications in which pressure control is required. They are used, for example, in the supply of technical gases in the high pressure area.